MwlRCT
PLEASE, help to make this indicator a mtf
PLEASE, help to make this indicator a mtf
Attached File(s)
StepMA pdf nmc 3.142 + arrows.mq4
18 KB
|
200 downloads
I will code your pivot EAs for no charge 24 replies
I will code your scalping EAs for no charge 163 replies
Oanda MT4 - Indicators and EAs not showing 2 replies
EAs and indicators relating to moutaki... 22 replies
InterbankFX has loaded its MT4 platform with custom EAs, indicators and scripts 1 reply
Disliked{quote} No... Unfortunately EA is not working properly. it's opening non-stop orders in both sides and on the middle of rectangle... Something wrong {image}Ignored
Disliked@BestTraderEv, Could you help with coding candle scanner on the watchlist as shown on image below?? Thanks in advance {image}Ignored
Disliked{quote} \ hello i was wondering if u can help me make this indi non lag if possible...thanks so much.. it somitmes lags and somtimes it does not... {file}Ignored
DislikedHello dear coders and traders, I need an indicator that will show me in MetaTrader or TradingView if this pattern is formed on the chart. {image} {image}Ignored
Disliked{quote} This tool is just good for trends. In a flat, on the contrary, it opens a bunch of trades if it hits the edges. That is why I asked for it to be redesigned, so that it would open trades only after the candlestick goes over the edge and closes there, outside the rectangle. Thus, these friking fuses in all directions will be cut off and unnecessary trades will not be opened. This is original mode on the pic. {image}Ignored
if(TradeStyle==Original) { if (LB<=LS && Bid>HighBox && Bid<HighBox+10*Point && HighBox!=0) { if(SendOrder(OP_BUY, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Ask,Digits))) TimeBar=Time[0]; } if (LB>=LS && Bid<LowBox && Bid>LowBox-10*Point) { if(SendOrder(OP_SELL, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Bid,Digits))) TimeBar=Time[0]; } }
if(TradeStyle==OnClose) { if (LB<=LS && Low[1]<HighBox && Close[1]>HighBox && HighBox!=0) { if(SendOrder(OP_BUY, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Ask,Digits))) TimeBar=Time[0]; } if (LB>=LS && High[1]>LowBox && Close[i]<LowBox && LowBox!=0) { if(SendOrder(OP_SELL, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Bid,Digits))) TimeBar=Time[0]; } }
HighBox=ObjectGet("Rectangle",OBJPROP_PRICE1); LowBox=ObjectGet("Rectangle",OBJPROP_PRICE2);
Disliked{quote} Thanks for reply. Is it possible on individual symbols? Then push alert as a pattern? RegardsIgnored
Disliked{quote} Of course it can be done if you provide the specific conditions. Your image isn't clear at all I will remind you that all we have are OHLC prices of candles, and we must find a pattern by comparing those prices in relation to previous candle(s). So, you need to provide more information that what you show in your image.Ignored
Disliked{quote} Of course it can be done if you provide the specific conditions. Your image isn't clear at all I will remind you that all we have are OHLC prices of candles, and we must find a pattern by comparing those prices in relation to previous candle(s). So, you need to provide more information that what you show in your image.Ignored
Disliked{quote} The original logic for opening trades is: if(TradeStyle==Original) { if (LB<=LS && Bid>HighBox && Bid<HighBox+10*Point && HighBox!=0) { if(SendOrder(OP_BUY, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Ask,Digits))) TimeBar=Time[0]; } if (LB>=LS && Bid<LowBox && Bid>LowBox-10*Point) { if(SendOrder(OP_SELL, MaxLot==0?Lot:MaxLot*2, NormalizeDouble(Bid,Digits))) TimeBar=Time[0]; } } This means that a Buy order is placed when Bid is above Rectangle High and below Rectangle High + 10 points. A Sell order is placed when Bid is below Rectangle Low and...Ignored