Losers Complain, Winners Train!
Utah
![](https://resources.faireconomy.media/images/emojis/64/1f44d.png?v=15.1)
Auslanco 15min GBP/JPY startegy 630 replies
Auslanco-GBP/JPY Strength Indicator strategy 344 replies
My MT4 indicators for Auslanco's strategy 92 replies
Auslanco 15 minute Strategy Oanda FXManager Updates.. 62 replies
Questions About Auslanco's Trades 72 replies
Dislikedother question, where did you get ###QQE_Alert_MTF_v5###.mq4 ... i only have v3. Because your program apparently doesn't work/show up with v3
i must be falling behindIgnored
DislikedMono if you can explain the functioning more it will be beneficial
Thanks for your effortsIgnored
Dislikedthat's absolutely fantastic, is there a way you could program that exact indicator on VT Trader??Ignored
DislikedOriginally Posted by mono http://www.forexfactory.com/images/buttons/viewpost.gif
Ok Guys
Time for me to add to this thread.
I have created (or should I say modified) the original signal_bar indicator to reflect Auslanco's method across all timeframes at the same time on one screen.
Labels
GSMA = Gann Hi Low Activator 10 against Simple Moving Average (5 close) Cross
QQE = Quantitative Qualitative Estimation Indicator
LSR = Level Stop Reverse Indicator
Requirements
###Gann_HiLo_Activator_v2###.mq4
###QQE_Alert_MTF_v5###.mq4
MT4-LevelStop-Reverse-vB0-3.mq4
(Thanks to all the guys that developed the above indicators)
NOTE: Timeframes 15m and lower use the scalping parameters.
that's absolutely fantastic, is there a way you could program that exact indicator on VT Trader??Ignored
DislikedOk Guys
Time for me to add to this thread.
I have created (or should I say modified) the original signal_bar indicator to reflect Auslanco's method across all timeframes at the same time on one screen.
Labels
GSMA = Gann Hi Low Activator 10 against Simple Moving Average (5 close) Cross
QQE = Quantitative Qualitative Estimation Indicator
LSR = Level Stop Reverse Indicator
Requirements
###Gann_HiLo_Activator_v2###.mq4
###QQE_Alert_MTF_v5###.mq4
MT4-LevelStop-Reverse-vB0-3.mq4
(Thanks to all the guys that developed the above indicators)
NOTE: Timeframes 15m and lower use the scalping parameters.Ignored
DislikedHi Karmo
Been waiting for you and the London boys to pull this thing up. Its been faffing about and doesn't want to show some muscle.Ignored
Dislikedseems like there is an error I could be mistaken, but from what i see right now the only time frames signaling a long on the LSR are the 15 min the rest are short yet your indicator says all long.
also can you correct the settings tab so its no longer saying macd and such, and maybe include settings for the indicators as wellIgnored
DislikedBasically Green for up(Buy), Red for down(Sell) depending on which time frame your focus is on.
E.G. For GSMA
When sma5 crosses up over the Gann line it goes green and indicates buy. Same applies in reverse and all other lables
Settings used
###Gann_HiLo_Activator_v2### = 10
SMA 5 on close
QQE smooth = 60 for 15m and lower else smooth 5 for higher timeframes
MT4-LevelStop-Reverse-vB0-3 = true,40,9,3,0 for 15m and lower else true,40,14,2.824,14Ignored
DislikedAm I the only bear here?? I went short 6 hrs ago this morning at the worst possible entry of 233.56. Impatient and wasn't thinking. Minor relief now but not expecting a profit. Breakeven would be good!Ignored
DislikedIt all depends on what settings you have, but i'll make the setting adjustable for each persons preference.Ignored
Dislikedon Mono's new system, does anyone else's "Daily Average" say 278?Ignored
DislikedAm I the only bear here?? I went short 6 hrs ago this morning at the worst possible entry of 233.56. Impatient and wasn't thinking. Minor relief now but not expecting a profit. Breakeven would be good!Ignored
DislikedWell the QQE alert on AUS 15min startegy is beeping - that should give you some relief.
Wish it would shu up though...Ignored